Boutique slm
Bons plans
34.45 EUR
Dive Rite Cavern / Safety Reel - 36
Dive Rite Cavern / Safety Reel - 36. Cavern/Safety ReelThe Cavern/Safety Reel came about as North Florida cave training agencies began establishing standards in cave training. The established standard for cavern divers was to limit penetration no farther than 130 linear feet from daylight. Experienced cave divers use the Cavern/Safety reel as a jump reel or as a back up for security. Wreck divers will use this reel for shooting lift bags. The frame of the reel comes with a series of pre-drilled holes so divers can change positions from a top-mount handle, to a side-mount handle or a left-hand operated reel. The spool is held in place with a stainless steel "C" clip so replacing the spool or cleaning up a jammed reel is simple.- White, DuPont fiber braid line provides strength and minimizes fraying.- Orange, Dacron line does not stretch, keeping firm tension.- Cave series reels use #24 braid line giving 220-lbs of breakage strength. Wreck series reels use #36 braid line giving 350-lbs of breakage strength.- Injection molded polycarbonate spools resist breakage and cracking.- Marine grade stainless steel frame and axle are corrosion resistant.- Marine grade stainless steel bolt snap is corrosion resistant.- T-top lockdown screw for easy grip- 1 lb (0.45 kg)TIPS:1.Before diving with a new reel (or a dry reel that has been in storage), put the reel in a bucket of water and after soaking, pay out the entire length of line and reel it back in. This will moisten the line, precluding it from swelling on the reel and further preventing the possibility of jamming or damaging the spool.2.As with most dive equipment, you should rinse your reel with fresh water following each dive. You should also periodically disassemble the reel, and remove any build up of salt or sediment on its internal parts.3.Dive Rite recommends pulling some or all of the line off the spool before each dive, then rewinding it neatly but not too tightly, so as to prevent the possibility of jamming during line deployment.4.Finally, too much line on the spool can cause jams during initial deployment, if you are having a problem with jams try removing 10 or 15 feet of line.
19.01 EUR
Dive Rite Scissors Trauma
Dive Rite Scissors Trauma. Coordinating with our line of harness pockets is our unique cutting device sheaths that snap into our pocket daisy chain loops. Using heavy-duty Annex clips that slip through daisy chain loops and snap into place. These clips are rugged and won’t come unclasped underwater. To remove, you must pinch the ends slightly to get the clip to release…easy enough, but not so easy that it comes undone all on its own. The sheath clip will also close around cylinder hose retainers, wrist straps, gaiters or a chest strap. If desired, the Annex clips can be removed and the sheath worn on a standard 2-inch waist belt. A quick-release Velcro lanyard keeps the Z-knife in firmly in place.Carried by ocean divers for use in cutting wire or fishing nets, our heavy-duty Titanium Shears have salt-water ready 440 stainless steel construction. - 440 grade stainless steel blade- Annex clips can be removed and sheath worn on waist belt, if preferred- Quick-release Velcro lanyard keeps shears securely inside the pocket- Nylon webbing pouch - Pouch is 7-inches high x 2-inches wide (17 cm x 5 cm)- Shears are 8-inches in length and 4-inches wide at the handle (20 cm x 10 cm)- 3.8-oz (108 grams) with pouch
8.87 EUR
725.61 EUR
Dive Rite Led Rx2 Canister Light
Dive Rite Led Rx2 Canister Light. The RX2 is Dive Rite-s most advanced lighting system utilizing an intelligent microprocessor control unit that keeps the light operating at peak efficiency. The smart controller features:* Battery State-of-Charge Monitoring* Low Battery Indication at Turn On* Temperature Monitoring for Device Protection* OFF - HIGH - LOW Selection via Rotary SwitchUnique in the marketplace is the RX2s dual power selector switch now located on the light head instead of the canister. This provides easy access to switch power modes on the fly. At full power, the RX2 has a four hour burn time and eight hours at half power.**However, using smart technology, the RX2-s microprocessor -thinks- for the diver and automatically switches from full power to half power to extend battery run-time while maintaining usable light (see chart located in DOWNLOADS for power management details). A key added safety feature is the battery check function. The diver can easily check battery state-of-charge by simply switching the unit on. If the unit flashes three rapid pulses, the diver knows that the battery is low before the dive.In addition, heat-sensing technology enables the light to be used out of the water safely and reliably as the RX2 continuously monitors heat emission from the LEDs. The light will automatically reduce output preventing the LEDs from overheating, a common issue for LEDs in an enclosed fixture. This allows the diver to use the light on land post-dive at the campsite, boat dock, or any land-based activity requiring illumination.The RX2 employs four, Luxeon® Rebel- LEDs at a system lumen rating of 880 lumens at full power. At one meter, the RX2 boasts a LUX rating greater than 11,000 lumens (see DOWNLOADS and TECH SPECS for a complete listing of technical data and specifications).Designed for technical diving, the RX2 sports a tight 10-degree beam that is useful for signaling, yet covers enough area to illuminate the surrounding environment for better awareness as well as viewing pleasure.The RX2 comes standard with a Goodman metal hand mount (elastic hand mount available upon request). The RX2 NiMH batteries do not contain lithium and therefore are not subject to TSA travel restrictions. NiMH charger comes standard with a US power cord and automatically adjusts to 110/220 volts AC and 50/60Hz frequency. Other power cords are available upon request.The Dive Rite RX2 is proudly designed, manufactured, and assembled in the USA and is RoHS compliant to European environmental standards. 880 system lumens @ full powerLux ratings: 11,440 @ 1 meter, 2,800 @ 2 meters, 1,320 @ 3 metersLuxeon® Rebel- 4 LED array, 10,000 hour life, RoHS compliant to European standardsColor Correlated Temperature (CCT): 6,500 KelvinPower Consumption - 12Watts @ maximum output using a 12v 4500ma NiMH slimline battery. Does not fall under TSA travel restrictions. NiMH charger automatically adjusts to 110/220 volts AC and 50/60Hz frequency. US power cord is standard while other cords available upon request.4-hour burn time at full power; 8-hour burn time at half power (All burn times stated using fresh conditioned batteries).When battery drops to 11.2v, light auto switches to 50% power. At 10.2V-8V light auto switches to 25% power. Light output tapers until battery drops to 8V at which point the unit shuts down to protect the battery from cell reversal.Rotary switch located on light head selects full power, half power and off settings.Depth rating - 500 feet (152 m)Ships standard with Goodman metal hand mount. Elastic hand mount available upon request.Includes protective case.3.8 lbs (1.72 kg) including battery, Buoyancy (-1.25 lbs)Slimline canister: 9-(L) x 2.6- (dia.)[22.86 cm x 6.60 cm]
275.69 EUR
Dive Rite Travelpac
Dive Rite Travelpac. The ultimate recreational travel rig, our new TravelPac is an all-in-one harness and wing that is a hybrid combination of the Travel EXP wing and TransPac harness. Weighing only 5 lbs 13 oz (2.62 kg), the TravelPac is streamlined to reduce the weight of the rig keeping it lightweight and small-profile, which is ideal for traveling to warm-water destinations.At 27lbs/12kg of lift, the TravelPac can accommodate one 80ft3/12 L tank with additional weight in pockets or a weight belt not to exceed 16lbs. (16lb QB Weight Pockets are sold separately).Features:- Hardware is streamlined with one epaulet on the left shoulder. - Standard shoulder pivots.- 2 bent chest D-rings. - 2 waist D-rings.- Stainless steel belt buckle. - TransPac sideplates are narrower and give more room on the waist belt for accessories.- Includes a chest strap, one standard 36-inch cam strap w/stainless buckle and 1.5-inch crotch strap.- Weight: 5 lbs 13 oz (2.62 kg)- Dimensions: 22-in H x 14-in W (55.9cm x 35.6cm)
275.69 EUR
Dive Rite Voyagerpac
Dive Rite Voyagerpac. The VoyagerPac BCD is an all-in-one harness and wing that is a hybrid combination of the Voyager EXP wing and TransPac harness. Weighing only 6 lbs (2.72 kg), this lightweight travel BCD is certainly not a "lightweight" in other areas. Built from the same rugged materials as our technical harness and wing, the VoyagerPac is impressively constructed and will last for years.At 40lbs/20kg of lift, the VoyagerPac is designed for single, steel tanks or divers who require heavy weights due to cold water exposure protection. The VoyagerPac will accommodate one 95ft3/15 L tank with additional weight in pockets or a weight belt not to exceed 32lbs. (32lb QB Weight Pockets are sold separately).Features:- Hardware is streamlined with one epaulet on the left shoulder.- Standard shoulder pivots.- 2 bent chest D-rings.- 2 waist D-rings.- Stainless steel belt buckle. - TransPac sideplates are narrower and give more room on the waist belt for accessories. - Includes a chest strap, one standard 36-inch cam strap w/stainless buckle and 1.5-inch crotch strap. - Weight: 6 lbs (2.72 kg) - Dimensions: 22.5-in H x 19-in W (57.2 cm x 48.3 cm)
16.02 EUR
Dive Rite Z Knife
Dive Rite Z Knife. Z Knife- Daisy Chain Clip.Coordinating with our new line of harness pockets is our unique cutting device sheaths that snap into our pocket daisy chain loops. Using heavy-duty Annex clips that slip through daisy chain loops and snap into place. These clips are rugged and won’t come unclasped underwater. To remove, you must pinch the ends slightly to get the clip to release…easy enough, but not so easy that it comes undone all on its own. The sheath clip will also close around cylinder hose retainers, wrist straps, gaiters or a chest strap. A quick-release Velcro lanyard keeps the Z-knife in firmly in place.In the early 1980s cave divers were in need of small, line-cutting devices. Since the application was strictly for cutting lines, they looked to other sports and adopted the parachute line cutter known as a Z-Knife. The Z-knife was a protected blade stored away in a pouch. Today, the pouches have evolved, but the knife is still the same one parachutists use to cut away a chute. Sharper than a dive knife, the Z-Knife is preferred for cutting through monofilament and braid line.Features:- Z-knife blade made of 440 grade stainless steel. - Quick-release Velcro lanyard keeps Z-knife securely inside the pocket.- Nylon webbing pouch. - Pouch is 4-inches high x 2.75-inches wide (10 cm x 7 cm).- Knife is 3-inches in length (7.6cm).- 1.2-oz (34 grams).- Apply a light coat of silicone grease to the knife blade to help protect against corrosion.
449.50 EUR
421.82 EUR
Dive Rite Nitek Trio
Dive Rite Nitek Trio. The new NiTek Trio is a three-gas Nitrox computer that is easy-to-read and easy to use.
It includes the following features:
- Dot matrix LCD displays dive profile in a graph format.
- All three mixes are programmable from 21%-99% Nitrox.
- A deep stop feature allows for safety stops at deeper depths.
- Three user adjustable safety factor levels.
- Digital compass integrated into the dot matrix display.
Worn on the wrist or as part of an SPG console, the NiTek Trio turns on automatically upon descent is an ideal primary or back up dive computer.
Underwater, divers can switch between mixes with the push of a button.
Upon surfacing, the NiTek Trio will maintain the gas mixture entered until midnight, when it clears and must be reset the following day.
Using a modified Buhlmann ZH-L16 algorithm, the NiTek Trio can calculate decompression stop times for required stops as deep as 90-feet.
Technical Features:
- Oxygen exposure tracking display via FO2, PO2 and OLI (oxygen limit index) bar graph.
- Visible warnings for violation of ascent rate, no decompression state, mandatory decompression stops (if necessary) and if diver has ascended above a mandatory decompression stop ceiling.
- Nitrox specific warnings occur if the diver exceeds a PO2 limit of 1.4 for Mix 1 and PO2 limit of 1.6 for Mix 2.
- Date, time and water temperature display.
- Current and max depth display.
- Dive time elapsed and no-decompression time remaining display.
- Desaturation and time-to-fly information display.
- Back lighting with 5 second LCD visible in all light conditions.
- Logbook will hold up to 30 hours (or 60 dives) based on 30 second profiling intervals.
- Maximum depth 328 feet (100 meters) in dive mode and 656 feet (200 meters) in gauge mode.
- Adjusts automatically for altitude up to 19,685 (6,000 meters).
- Imperial and metric units of measure.
- User replaceable lithium CR2032 battery.
- 2.5-inch diameter X 1.0-inch high (6.2cm x 2.5cm) (fits existing NiTek wrist mount and consoles).
- 4 ounces (115 grams).
466.59 EUR
Dive Rite Nitek Trio Console
Dive Rite Nitek Trio Console. The NiTek Computer Console includes the NiTek Trio dive computer together with the Dive Rite Compact SPG.
An optional compass can be mounted on the HP hose of the computer console. Attach our AC2019 Hose Clip Retainer and HW1026 Medium Stainless Steel Bolt Snap to the NiTek Computer Console to streamline hoses and maintain a trim profile in the water.
The NiTek Trio is a user-friendly, easy-to-read dive computer with Nitrox capabilities.
Worn on the wrist or as part of an SPG console, the NiTek Trio turns on automatically upon descent and monitors up to three different gas mixes.
Upon surfacing, the NiTek Trio will maintain the diver-set gas mixture until midnight, when it clears and must be reset the following day.
Using a modified Buhlmann ZH-L16 algorithm, the NiTek Trio can calculate decompression stop times for required stops as deep as 90-feet.
Simple to program, the NiTek Trio has intuitive menus that are easy to understand without complex instructions.
A large, 2.5-inch (6.35 cm) screen makes it easy to keep track of the dive at a glance.
Our Compact SPG is calibrated to 5000-psi in 100-psi increments (also available in BAR) and comes Nitrox ready.
It features a chrome-plated brass housing and a Bourdon tube mechanism providing the greatest degree of accuracy and reliability.
The luminescent dial makes it easier to read in low light situations.
Technical Features:
- Monitors up to 3 different gas mixtures including nitrogen and oxygen.
- Oxygen exposure tracking display via FO2, PO2 and OLI (oxygen limit index) bar graph.
- Visible warnings for violation of ascent rate, no decompression state, mandatory decompression stops (if necessary) and if diver has ascended -above a mandatory decompression stop ceiling.
- Nitrox specific warnings occur if the diver exceeds a PO2 limit of 1.4 for Mix 1 and PO2 limit of 1.6 for Mix 2.
- Date, time and water temperature display.
- Current and max depth display.
- Dive time elapsed and no-decompression time remaining display.
- Desaturation and time-to-fly information display.
- Back lighting with 5 second LCD visible in all light conditions.
- Logbook will hold up to 30 hours (or 60 dives) based on 30 second profiling intervals.
- Underwater gas switching with the push of a button.
- Modified Buhlmann ZH-L16 algorithm.
- Decompression stop times for stops as deep as 90-feet.
- PC uploadable with NiTek Dive Log software and optional PC interface (note does not work with Vista 64 bit operating systems).
- Maximum depth 328 feet (100 meters) in dive mode and 656 feet (200 meters) in gauge mode.
- Adjusts automatically for altitude up to 19,685 (6,000 meters).
- Imperial and Metric units of measure.
- User replaceable lithium CR2032 battery.
- Compact SPG has a 1.5-inch (3.81cm) diameter scratch and impact resistant polycarbonate face.
- SPG is in BAR.
- 1.31lb (0.59kg).
23.62 EUR
Dive Rite Nitek Duo/ Trio Bag
Dive Rite Nitek Duo/ Trio Bag. Bag for Nitek Duo/ Trio dive computer from Dive Rite.
178.22 EUR
Dive Rite Nitek Duo/trio - Docking Station
Dive Rite Nitek Duo/trio - Docking Station. The NiTek Duo Docking Station is used to download dives from a NiTek Duo computer.
The docking station holds the NiTek Duo in place and connects to a personal computer using the USB cable provided.
CO8110 NiTek Duo Docking Station and NiTeklogic Software:
The NiTeklogic software is a logbook program that downloads and stores dives from the NiTek Duo computer.
The NiTeklogic software displays all of the information about each stored dive and allows you to add information to each dive.
As a bonus, a DEMO version of Voyager Decompression Software has also been included on the CD.
Computer requirements:
To use the NiTek Duo Docking Station and NiTeklogic software you need a computer running Windows 98, XP, or 2000, a CD-ROM drive, and an available USB port.
5.54 EUR
Dive Rite Nitek Duo Cover Lens
Dive Rite Nitek Duo Cover Lens. Screen protector Nitek Duo Dive Rite computer.
34.29 EUR
Dive Rite Stage Kit So80
Dive Rite Stage Kit So80. Our Stage Bottle Rigging comes with everything a diver needs to correctly set up secondary bottles for years of technical diving.Our 1-inch (2.54 cm) nylon webbing with 2,200 lbs (998 kgs) tensile strength forms the carrying strap. Resistant to breakage, rot and splitting, nylon webbing creates a durable and long-lasting foundation for stage rigging, yet can be cut free in case of entanglement. Rugged elastic hose retainer band resists rolling and tearing and has the right amount of stretch.A large webbing loop on the retainer is easy to grip even with gloves on.Marine grade stainless steel cylinder clamps and hardware are saltwater ready and resistant to corrosion.A 1-inch (2.54 cm) piece of tubular webbing and a short piece of clear tube are provided to cover the tank clamp and screw for abrasion protection.A longer piece of clear plastic tubing slides over the nylon webbing to form a comfortable handle on the carrying strap. Features:* Stainless steel XL bolt snap * One-inch (2.54 cm) nylon webbing strap with 2,200 lbs (998 kgs) tensile strength.* Neoprene-infused elastic hose retainer band resists rolling, tearing and abrasion.* Marine grade stainless steel cylinder clamps and hardware are saltwater ready and resistant to corrosion* One-inch (2.54cm) tubular webbing, provides diver/tank clamp abrasion protection
6.73 EUR
Dive Rite Baseball Cap
Dive Rite Baseball Cap. Baseball cap from Dive Rite.
Sewn logo in 3 colors on the front part.